Skip to content
Thank you for visiting. We have opened up orders for the E-Series and G-series kits. Ford Kits Ship week of 10/18 and G-series kits ship First week of November!
Thank you for visiting. We have opened up orders for the E-Series and G-series kits. Ford Kits Ship week of 10/18 and G-series kits ship First week of November!

Ford Econoline Transmission Crossmember Drops ( Fits all '92-'14 Transmissions)

$75.00
SKU
Description:

**This item ships for free!**

Whether you use leaf springs or lift blocks to raise the rear of your van, you will need to consider the change in driveshaft angle coming off the back of the transfer case. If your driveline angle is too steep, you will have vibrations at speed. 

Our crossmember extension solution allows you affordably lower your transmission cross-member the correct amount for 4-6 inches of lift at the rear axle, reducing driveline vibration. The kit works with the E40D, 4R100, 5R110, and 4R75 transmissions alike.

Alignment is very straightforward. Our plates come labeled left and right, and are pre-cleaned for weld-in locations. The plates are backed with a pre-welded support washer that sits snug up against the frame of the vehicle and right on top of the cross-member, showing you just where to weld it in.

Installation requires a 9/16" drill bit to make 1 hole in your crossmember. If you do not have an appropriate drill bit, choose the "add drill bit" option at checkout.

Note: If converting your E40D or 4R100 to 4x4, you may need to drill 2 more holes in the lower section of your crossmember because the spacing on the transmission mount 2WD vs. 4x4 is slightly different.  

(updated product photography coming)

Fitment Designed for: 

Van Side - 1992-2014 Ford E-150, E-E250, E-350, E-450 

Tools Required:

Pneumatic impact gun and/or wrench to remove crossmember, appropriate sockets, wrenches, pneumatic or otherwise grinder for surface weld-prep, pilot drill bit(s), minimum 220v welder w/ shielding gas, touch up paint, chassis or spray paint recommended, torque wrench recommended. 

Construction Notes:

Plates are 1/4" A36 steel and come with welded Williams washers for additional support. Extensions are powder coated for longevity and pre-cleaned to indicate appropriate weld pattern. After welding in and allowing to cool slightly, we recommend painting your extensions and crossmember, effectively bake setting your paint.

Tips / Skill Level:

1-10 (10 being most difficult) Level 3, does require welding

This product may work with other model vehicles. 

Install transmission crossmember, torque upper 19mm nuts to 60 ft lbs, and mount nuts to 66 ft lbs

Shipping, Fulfillment, Taxes, Quality, and Returns
  • Shipping: Our components are carefully wrapped and packaged and ship UPS, USPS, or FedEx, depending on what is available. If you require a particular carrier, please contact us ahead of your purchase.  Customers in Colorado may arrange for in-person pickup within 1-2 business days of purchase. 
  • Shipping/Fulfillment time for components: We typically ship within 1-2 business days of your order and we carefully monitor our inventory. In the event that we are unable to meet that timeframe, we will contact you and arrange either a full refund or a timeframe for fulfillment agreeable to the customer. 
  • Taxes: Colorado residents must pay sales tax of 7.5%, no sales tax is collected on out-of-state shipments currently. 
  • Quality and Returns: We are consistently complimented on the quality of our products and the ease of install. Components are hand-built here almost exclusively in Colorado by seasoned professionals who are fanatics about design and execution. If you are in any way disappointed in the components we will issue a full refund less the cost of shipping when the product is returned. If you decide to return any components that didn't apply to your build or you changed your mind about, shipping and a 15% restocking fee will be deducted from the purchase refund.